FIRE POLY FP50

INTERIOR/EXTERIOR FIRE RETARDANT
COATING or SPRAY FOR ALL WOOD PRODUCTS
PLYWOOD ● LUMBER ● TIMBER

  CLASSIFIED
19P5
FIRE RETARDANT COATING
SURFACE BURNING CHARACTERISTICS OF APPLIED COATING

Surface

Douglas fir

---

Flame spread	20
Smoke developed	90
Number of preliminary coats	None
Rate per coat (ft2/gal)	--
Number of fire retardant coats	3
Rate per coat (ft2/gal)	500
Number of overcoats	None
Rate per coat (ft2/gal)	--
Flash point of liquid coating:
Fire retarding coating - closed cup,	no flash

FIRE POLY FP50	TECHNICAL DATA INTERIOR CLASS A RATING

PRODUCT DESCRIPTION:    Aqueous Based Resin

PRODUCT ANALYSIS
Total Solids	42%		PH	2.6 - 2.9
Weight per gallon	10.5 lbs		Flash point	Non-Flammable
Specific gravity	1.33		Color	Water clear at 78°F. - Slight haze at 50°F. or lower
Volatability	Non-Volatile		Solvents	Water(Contains no petroleum or derivatives of petroleum)
Anti-Fungus	excellent Resistance		Bacterial	Good Resistance
Linear shrinkage	None		Moisture Absorption	None
Corrosive	Mildly		Toxic	None (when dry)
Insects, rodents, aspergilli And other types of molds	Excellent resistance		Termites	Excellent resistance
Preservative for wood	None		Scrubability	1000 cycles

RECOMMENDED USE: Interior Class A Rating (Flame spread less than 25)

FLAME SAFE FIRE POLY 50 is a fire retardant and wood preservative coating. It can be used on:

Solid Hardwoods	Plywood	OSB
Paneling	Particle Board	MDF

ENVIRONMENTAL REGULATION:

This product complies will U. S. Federal Regulations concerning the use of lead in paint and hydrocarbon emissions.

QUICK REFERENCE FOR APPLYING FIRE POLY FP 50

MATERIAL	APPLICATION	COVERAGE
Interior wood Any type	Treat before, during or after construction. Be sure surface is clean and dry before treating. Apply with sprayer head held at 8 to 12 inches from surface Apply with brush or roller. May be necessary to wipe on hardwood surfaces Treat all surface areas where possible Do not expose treated area to moisture for 24 hours.	Apply three (3) coats at 500 sq. ft. per gallon with the final coverage rate of 166.3 sq. ft. per gallon

INTERIOR WOODS            All surfaces to be treated must be clean and dry. Fire Poly 50 is water-based, clear liquid that becomes insoluble when dry. Fire Poly 50 also acts mold and mildew protector and repels insects. If over coating is intended, Fire Poly 50 is an excellent surface primer for use under latex paints or can be use as a finished coat overwater based stains. DO NOT DILUTE OR MIX FIRE POLY 100 WITH ANY OTHER PRODUCTS.    Avoid wasteful runs and dripping.  It should be noted that unlike some products, materials treated with Fire Poly 50 require no special cutting tools or special fasteners. Contact parts of any equipment should be stainless steel or plastic to prevent chemical reaction and breakdown. Storage may be done in polyethylene containers.      Structures can be made fire resistant. Use on substrates athat are enclosed and/or in areas that are warm and dry. Fire Poly FP 50 creates a varnish like coating that provides a long term fire retardant protection.

CAUTION:

          Product must not freeze. It must not be thinned or diluted.

OVERSPRAY:

        The overspray will not harm plants or animals. Spills can be flushed with water. A rag wetted with   bleach and water mix will clean up spotting.

CLEAN UP PROCEDURE:

          Airless Equipment.

1. Run clear water through the system until coating is flushed out. When minor sudsing on surface stops, the system is flushed.

2. Run bleach and water mix (1 part to 4 parts) through system as solvent for cleaning any residue.

            3. Repeat Step 1 if any foaming occurs in Step 2.

            4. Lubricate system as specified by equipment manufacturer to combat rusting.

If two or more applications are planned in the same day, the sprayer can be kept clean by running water through the system between applications.

          Brushes/Rollers.

              1. Clean immediately after use.

              2. Wash thoroughly with bleach and water mix (1 part to 4 parts).

SAFETY FIRST

Use approved safety devices (ropes, belts, ridge hooks, ladder, etc.) When working on steep or high areas. Take EXTREME CARE not to step on wet treated area. Surface may be slick until dry.

It is good practice to wear respirator or mask and protect hands with rubber gloves when spraying any coating or chemical. When engineered air control is not feasible, use properly maintained and properly fitted NIOSH approved respirator for solvent vapors. A dusk mask does not provide protection against vapors.

If eye contact occurs, flood with water for fifteen (15) minutes and call a physician. KEEP OUT OF REACH OF CHILDREN. DO NOT TAKE INTERNALLY.

HOME | FIRE RETARDANT COATINGS | FIRE RETARDANT WOOD | HOW IT WORKS | CONTACT US

The information contained herein is the property of Fire Prevention Technologies d/b/a Flame Safe Chemical Corporation and Flame Safe Wood Products, Inc. ©1990 revised 8/20/2009 Revised 2012